CIG 2500

This machine has been converted from a cantilever tracer to a full CNC gantry configuration with a Burny 3 CNC controller giving the added bonus of using less floor area the compared to a cantilever. This machine has been inspected and all functions are operational.

Due to this machine’s less powerful drive system it is unable to accommodate the plasma process without a drive upgrade. If a drive upgrade werecompleted we would reclassify the above as A-class and provide a full warranty and service package.

Features include

• Burny 3 CNC Controller
• Two CIG 2 seat oxy-LPG torches
• Two electric lifters for positioned torch stations
• Frictional drives inspected in both axes
• Hand valve operation of all gases.
• Mechanical clutches in both axes
• Gas manifold for multiple torches
• Central control panel
• Stewart Warner copy controller and tracing eye(tracing eye not in working condition)
• Amplifier and Burny 3  inspected for faults
• Useable cutting area of 2.4m wide x 6m long

Koike 2500J

A Koike 2500J heavy duty cantilever machine, 2.4 m wide by 6 m long, that has had the addition of four high-quality Koike 3-seat torches on heavy duty electric torch positioning lifters complete with manual oxy-fuel torches valves.

The older HL81 controller comes in high power configuration allowing it to run the associated Dynatec drive motors. This machine will provide a genuine 2.5m wide x 6m long useable cutting area and is fitted with a NC3 Hybrid controller**.

• Four motorised torch stations
• Four Koike -style machine torches
• Friction drives in both axes
• Solenoid operation of all gases including oxygen cutting stream
• Oxygen blow off valve to prevent damage to cut parts
• Hi-Lo per heat
• Gas manifold for multiple torches
• High speed HL81 controller with full options such as corner slow down, high speed and CNC interface options
• Useable cutting area of 2400mm wide x 6000mm long (could be extended by customer request)
• Comes set up for both teach tracing into the Burny and straight tracing
• Complete new gas supply and flash-back system
• NC3 hybrid NC Controller**

**Please note that the NC3 is not a full CNC controller and is capable of only copy-trace and standard shape operations only. To bring the machine up to full CNC capabilities the addition of a Burny 2.5 would be required for additional investment.

Hanco 2000

This has been fully converted to CNC control and comes with a 70amp dual-gas plasma system with auto-voltage height sensing. This profiler has been inspected and all functions are operational. This converted tracing head system has 1.8 x 4m useable cutting area.

Due to this machine’s more powerful drive system it lends itself to accommodate the plasma process without a drive upgrade. If the plasma process was added, we would reclassify the above as A-class and provide a full warranty and service package for an additional cost.

• Lynx CNC Controller
• One electric lifter for positioned torch stations
• One Harris style oxy-lpg machine torch
• Frictional drives in both axes
• Hand valve operation of all gases.
• Thermal Dynamics SR-4 automatic voltage height sensing system for plasma torch
• Thermal Dynamics Stak Pak 70 amp plasma system (1.6-12 mm capacity)
• Mechanical clutches in both axes
• Gas manifold for multiple torches
• Amplifier inspected for faults
• Useable cutting area of 1.8m wide x 4m long

PC 150

This PC 150 has been converted from a cantilever tracer to a full CNC configuration with a Burny 2.5 CNC controller.  This machine has been inspected that all functions are operational and has a 2.4 x 1.5m useable cutting area .

Due to this machine’s less powerful drive system it is unable to accommodate the plasma process without a drive upgrade. If the upgrade were completed we would reclassify the above as A-class and provide a full warranty and service package.

• Burny 2.5 CNC Controller
• Two CIG 2 seat oxy-lpg torches
• Two hand lifters for positioned torch stations
• Frictional drives inspected in both axes
• Hand valve operation of all gases.
• Mechanical clutches in both axes
• Gas manifold for multiple torches
• Central control panel
• Stewart Warner copy controller and tracing eye(tracing eye not in working condition)
• Amplifier and Burny 2.5  inspected for faults
• Useable cutting area of 2.4m wide x 1.5m long